The transparent panel in a viewing window is the only part of a niche that can break, scratch or yellow Choosing between ordinary glass, toughened glass, laminated glass and acrylic is not a question of price — it is whether five years from now, you can still read the line of text on the urn through it.

Ordinary annealed glass: good transmission, cheap, hard surface, but it breaks into large sharp shards. It is the last thing that belongs in a niche, because those shards land directly on the urn.
Toughened glass: four to five times the strength of ordinary glass, and it breaks into small granules, so it is less dangerous. But it carries a spontaneous breakage rate of roughly three in a thousand from nickel sulphide inclusions. Window sizes are small so the risk is low, but when it happens inside a sealed niche clearing up is miserable.
Laminated glass: two sheets bonded through a PVB or SGP interlayer. Broken, it stays stuck to the film and does not fly apart, and it retains some strength. This is the most suitable material for a niche window — 5+5 or 6+6, giving 10–11 mm overall.
Acrylic (PMMA): 92% light transmission, slightly better than glass half the weight ten times the impact resistance, and it does not shatter. But surface hardness is only around 2H, so a cloth with grit in it leaves scratches, and it attracts dust by static.
Acrylic's biggest problem is not strength, it is ageing Standard extruded sheet begins to yellow in three to five years under UV and the heat of the light strip, losing about 1% transmission a year. A niche window sits directly in front of the strip, running 5–10°C above ambient, which accelerates the process.
Glass does not yellow. That is its overwhelming advantage in a niche — twenty years later, wipe it and it is still clear.
Acrylic's second problem is cleaning Columbarium housekeeping uses a damp cloth, and if that cloth carries fine grit it leaves a haze of scratches. Wipe one window for five years and the surface becomes a fine fog; from outside, the urn is blurred.
Glass thickness follows area. Under 0.05 m² (about 250 × 200), 5 mm single or 5+5 laminated is enough; 0.05–0.1 m², use 6 mm or 6+6; above 0.1 m², laminated is mandatory, or add a mullion.
Acrylic's equivalent thickness is about 0.6 times glass. Roughly, 3 mm acrylic matches 5 mm glass in stiffness. But acrylic that lacks stiffness dishes visibly under a hand, which looks poor.
Once a niche window reaches 300 × 250 or more, acrylic has to go to 5 mm, at which point it is no longer cheaper than laminated glass.
The edge of glass is its weak point. A niche window must be edge-polished — at least a fine grind, never a raw cut edge. Raw edges crack under installation stress and thermal stress.
Three fixing methods:
- Trim and screws: most secure, and demountable. - Structural adhesive: cleanest, but replacing the glass means cutting the adhesive, which damages the coating. - Groove and gasket: glass set into a folded groove in the panel with a gasket. The usual method in volume production.
Whichever is used there must be an elastomeric pad (EPDM or silicone) between glass and metal — never direct contact. Hard contact chips the edge under the vibration of a closing door.
Single glazing fogs on the inside in the plum-rain season, because humidity inside the niche is high and the glass is cold.
The interlayer in laminated glass provides some thermal resistance and reduces condensation, but does not eliminate it. What actually works is keeping the carcass ventilated through its breathing holes, plus the 2 mm vent gap on the inside of the window.
A fully sealed window in a fully sealed carcass is the combination most prone to fogging.

Standard niche: 5+5 laminated, edge-polished, trim or groove fixing. About 40% more than ordinary glass, but the only option that cannot damage the urn when it breaks.
High niches (above 1.8 m): laminated, without exception. Replacing glass means a ladder, and a person on a ladder prising off a trim is a bigger risk than the glass itself.
Very tight budget, very small window (under 200 × 150): 3 mm acrylic is acceptable, provided you accept yellowing and surface haze in three to five years.
Not recommended: ordinary annealed glass, and single-sheet toughened glass, which is hard to clear up after spontaneous breakage.
A broken niche window is not simply "a new pane". It depends on the fixing.
With a trim, the trim comes off and the job takes half an hour. With a groove, the whole door panel has to come off, because the glass can only slide in from behind With structural adhesive, it is cut out, cleaned and re-beaded — a few panes a day at best.
Spares carry three traps of their own. Glass thickness, edge finish and laminate specification should be recorded in the as-built documentation; a batch of windows may be discontinued five years later, and a mismatched batch brings colour and thickness differences; and spares should be held at 3%–5% of the total, far cheaper than cutting a single pane later. Spares also need to be stored flat and away from light, since the interlayer fogs after about three years. Before replacing measure the groove depth — under 6 mm and the new pane will not seat A columbarium window is a bespoke item: keep the drawings, not just the finished product.
To state the conclusion first: the material of a niche window matters far more than the colour of the door. An old door panel is merely unattractive; a failed window damages the object inside. On a columbarium quotation, glass is often only a few dozen yuan, yet it is the one component capable of producing sharp fragments, and the one most likely to be "just matched with any pane".
Look at the edge. It should be a matte polished face, not a sharp bright edge. Any chipped edge should be rejected.
Look at the layer. View the glass edge-on: laminated glass shows a clear interlayer about 0.76 mm thick.
Press it. A palm on the centre of the window should not produce obvious deflection. Over 1 mm means insufficient thickness.
Light it. Shine a torch along the glass and look for bubbles, inclusions and ripple. Acrylic shows more ripple than glass.
Q: Acrylic does not break, so isn't it safer?
A: In the short term, yes. But a niche is a twenty-year timescale, and yellowing and scratching make the window pointless. Safety and durability have to be judged together.
Q: If glass breaks, will it fall onto the urn?
A: Laminated glass does not fall — it hangs in the frame like a web. That is exactly why it is worth the extra cost.
Q: Can safety film be applied to the window?
A: Yes, as a low-cost retrofit. But film lasts only five to eight years and lifts at the edges; laminated glass is the better answer.

For a niche window the answer is clear: laminated glass. It is not cheap, not light and not shatter-proof, but when it breaks it does not damage what is inside, and it will not yellow in twenty years. The logic of specifying a columbarium comes down to this — in the places nobody will ever maintain choose the option that fails safely.