Authenticity Guaranteed

Choosing the Niche Carcass Material: Galvanised, Aluminium, Stainless, Blockboard

Category: Technology News Columbarium Date: 2026-11-01 Browse: 12

The carcass of a niche is the part nobody sees — close the door and the family never looks at the sheet. Yet it decides what the niche looks like in twenty years: whether it rusts, whether it deforms, whether the door gap widens. The difference between the four mainstream materials is not which is better, but which is right for which position.

columbarium design

The Basic Parameters

Galvanised steel sheet: 0.5–0.8 mm thick, zinc coating 80–120 g/m² cost index 1.0 Works well — foldable, spot-weldable — and is the mainstream carcass material for columbarium niches.

Aluminium sheet: 1.0–1.5 mm thick, density 2.7 against steel's 7.85, so about a third of the weight for the same volume. It does not rust, but its stiffness is low: used alone as a load-bearing element it is soft and needs a profile frame.

Stainless steel: 0.5–0.8 mm thick, usually 304. Best corrosion resistance, three to four times the cost of galvanised, and harder to work — high springback on folding, and welds need post-treatment.

Blockboard: 15–18 mm thick. Good screw-holding, warm feel, but it fears damp: at 75% relative humidity an 18 mm board blisters within three months.

Galvanised: The Value Baseline

The logic of galvanising is that zinc rusts in place of steel. Zinc is more reactive than iron, so when the surface is scratched the zinc corrodes first and protects the cut edge. This is sacrificial anode protection, and it is why the material holds up in a damp environment.

As a niche carcass, galvanised sheet has three practical advantages: it folds well, so you can form stiffeners and return flanges; it spot-welds fast, so labour is low; and its price is stable. That is why most columbarium carcasses are galvanised — not because nothing better exists, but because nothing else delivers this combination at this price.

Aluminium: Light, But Not Stiff Enough

The great advantage of aluminium is weight — a carcass of the same size weighs a third of the steel version. On tall racking and on wide door panels, that saving is real.

The problem is stiffness. Aluminium's modulus of elasticity is about 70 GPa against steel's 206 GPa — a factor of three. At the same thickness an aluminium panel deflects three times as much. So a niche built in aluminium has to go to 1.2–1.5 mm, or carry a profile on the back Once the profile is added, part of the weight advantage is cancelled.

Aluminium also has a galvanic problem: in contact with steel in a damp environment it forms a cell and the aluminium corrodes. An aluminium carcass must not sit directly on a steel upright; there has to be an insulating pad between them.

Stainless: Best Corrosion Resistance, Used in the Right Places

304 stainless is virtually rust-free in a columbarium environment, and that is its value. It belongs in three positions: the bottom tier (close to the floor, where mopping throws moisture), niches against an external wall (large temperature swings, condensation), and coastal high-salt regions.

Using it everywhere does not pay. First, cost: a stainless carcass runs three to four times a galvanised one, which shows clearly in the unit price. Second, working: stainless has high springback when folded, so dimensional accuracy is worse than galvanised. Third, stainless does rust — chlorine-based cleaners and sea-salt spray both cause pitting in 304.

The sensible approach is selective: stainless for the base, for bottom-tier carcasses and for the row against the external wall; galvanised for everything else. Corrosion in a columbarium is never uniform — it appears first in the wettest few positions.

columbarium niche

Blockboard: Not Suited to a Columbarium

Blockboard and plywood look excellent in a showroom or a mock-up unit. In a working columbarium they have three hard failures:

Moisture deformation. Timber's equilibrium moisture content follows the environment, and columbarium humidity swings between 55% and 75%. An 18 mm board blisters in three months and the door frame no longer lines up within six.

Mould and insects. A timber carcass in a closed, humid environment is a nursery for mould and wood borers. Once it starts, the whole row has to come out.

Fire performance. Blockboard is combustible, and columbarium fire requirements are usually applied as public buildings. A timber carcass tends to fail inspection.

So blockboard can be a door facing or a decorative moulding. It cannot be a load-bearing carcass.

Mixed Use: The Most Rational Combination

Allocating material by position is the optimum for cost and life:

Bottom tier and external wall: stainless carcass, for moisture and corrosion.

Ordinary middle tiers: galvanised carcass, for value.

High tiers and wide door panels: aluminium with a profile frame, for weight.

Decorative faces: timber veneer panel, appearance only, no load.

This combination costs about 30% less than all-stainless and about 10% more than all-galvanised, but it takes care of the two positions that fail first — the bottom tier and the external wall. In columbarium maintenance records, those are the two most frequent sources of rework.

Frequently Asked Questions

Q: Will a galvanised carcass rust?

A: At cut edges and welds, yes. Where the zinc layer is broken, white rust appears first, then red. Cut edges need zinc-rich paint and welds need grinding and anti-rust coating.

Q: How much more does an aluminium carcass cost than galvanised?

A: About 50%–80% more in material, approaching double once the profiles are included. The weight saving only really pays on tall racking.

Q: How can I tell whether it is really 304?

A: Ask for the material certificate or use a magnet as a rough check (304 is weakly or non-magnetic). The reliable route is a mill certificate.

columbarium interior

Conclusion

Choosing a carcass material is essentially about putting the good material where things fail. Galvanised carries 80% of the volume, stainless holds the bottom tier and the external wall, aluminium handles weight, and timber veneer is only ever appearance. The life of a niche is not set by the most expensive sheet in it, but by what was used in the wettest position.

Continue reading articles with the same tags as this one
cache
Processed in 0.005298 Second.