Authenticity Guaranteed

Ancestral Tablet Sizes: A Home Altar Is Not a Columbarium

Category: Technology News Columbarium Date: 2026-10-31 Browse: 12

Ask "how big should the tablet be" and the first question back should be "where will it stand". Tablets on a home altar are measured in *cun*, with 4–6 cun the mainstream. Tablets in a columbarium tablet section are measured in millimetres, 200–300 mm high. Mix the two systems and the usual result is a tablet ordered to altar dimensions that jams on both sides when it goes into a niche-section tablet cell.

columbarium design

Two Systems, Two Contexts

Home altar. The tablet shares the altar with deity images, so its size is limited by the altar's depth and height and tradition asks for *he zi* — dimensions that land on auspicious numbers Hence the old *cun* system.

Columbarium tablet section. The tablet sits in a cell converted from a standard niche module, so its size is limited by the module, and the requirement is that it fits, reads, and does not block the neighbour. Hence millimetres.

Inside the niche itself. A minority of families place the tablet in the same niche as the urn. Here the tablet size follows the cavity, not the other way round.

Three contexts, three sets of constraints. Fix the context before discussing size.

Altar Tablets: What 4–6 Cun Means

One traditional *cun* is about 3.03 cm Four *cun* is roughly 12.1 cm, six *cun* roughly 18.2 cm — that is the width of the tablet. Height is usually counted as base plus body: a 4-cun tablet stands about 20–26 cm overall, a 6-cun about 30–38 cm, depending on whether there is a pedestal and whether it is two-tier.

Why is 4–6 cun the mainstream? Because it has to hold 7–12 characters. A single column on the face reads something like "Spirit Tablet of the Deceased Father, Mr X, Taboo-name Y" — around ten characters. At 15–20 mm per character, plus margins on both sides, you land neatly in a 12–18 cm width. Below 4 cun the characters must shrink under 12 mm, which is unreadable at a distance; above 6 cun the altar is not deep enough and the tablet blocks the deity images.

Columbarium Tablets: 200–300 mm High

Most tablet cells in a columbarium are converted standard niche cells: 250–300 mm internal width, 300–350 mm internal height. A tablet 200–300 mm high stands in the cell with room in front for a small incense holder or a photograph.

The logic behind this range is not auspicious numbers but sightlines. Tablet cells usually sit with their centre 1.3–1.6 m above the floor, at standing eye level. At 250 mm high with 20 mm characters, the text reads clearly a metre away; at 150 mm high the characters can only be 12 mm and you have to lean in.

Illuminance in the tablet section of a columbarium is typically 150–200 lux — a step below the niche area, to avoid direct strong light on urns. Under that level, small characters simply disappear.

How Many Characters Must Fit

A complete tablet face runs 7–15 characters:

Single: "Spirit Tablet of the Deceased Father, Mr X, Taboo-name Y" — 9–11 characters.

Joint husband and wife: 12–16 characters, usually set in two columns or side by side.

Ancestors of the lineage: "Spirit Tablet of the Ancestors of the X Lineage" — 9–11 characters.

At 15–20 mm per character, a 16-character double column needs 250–320 mm of width. That is precisely why joint tablets go up a size: pack 16 characters into a 4-cun width and they drop below 10 mm.

columbarium niche

How Tablet Size Relates to Niche Size

There is exactly one situation where the two must be matched: the tablet goes inside the niche, sharing the cell with the urn.

The minimum cavity then is 250 mm deep and 200 mm high. The common approach is to stand the tablet behind or beside the urn on a bracket. But the cavity was designed for the urn, so adding a tablet compresses the urn's working space and makes handling harder.

The far more common practice in a columbarium is a separate tablet section apart from the niches The tablet can then be made at full size and the niche keeps its space. In most columbaria the tablet section and the niche section are managed and numbered separately.

Three Limits on Custom Tablets

The module. Cell internal width is fixed. A tablet 20 mm too wide will not go in. Measure the clear internal width before ordering and leave 10 mm of margin.

The centre of gravity. Above 350 mm high, the base needs extra weight or width; otherwise the air movement when a door opens tips it forward.

The engraving depth. 0.8–1.5 mm reads best. Cut deeper than about 3 mm and the lettering shows through on a thin tablet — especially timber.

My advice: fix the system by context first (cun or millimetres), then fix the width by character count, then fix the maximum height by the cell. Get those three steps out of order and you will be redoing the drawing.

Frequently Asked Questions

Q: Will a 4-cun altar tablet fit a columbarium tablet cell?

A: Usually yes, since 4 cun is about 121 mm wide and most cells are over 250 mm internally. But check the height — a 4-cun tablet on a tall pedestal can exceed 300 mm.

Q: Must the tablet follow auspicious dimensions?

A: Home altars often do. Columbarium tablet sections generally impose no such requirement. Legibility and stability come first.

Q: How large should a joint husband-and-wife tablet be?

A: I suggest 40%–50% wider than a single tablet, or 50 mm taller. Sixteen characters squeezed into a 4-cun width become unreadable.

columbarium interior

Conclusion

There is no single standard for ancestral tablet size, only three sets of constraints: the cun system of the home altar, the module of the columbarium, and the cavity of the niche. Tablets in a columbarium answer to the cell; tablets at home answer to the altar. Ask "where does it stand" first and half the sizing problem is solved.

Continue reading articles with the same tags as this one
cache
Processed in 0.005203 Second.