"Will this urn actually fit?" It is the question families ask most often when they tour a columbarium, and it is the single most common failure point after a niche has been handed over. The problem is almost never the urn. It is the inner dimension. The quote sheet lists outer dimensions. The owner measures outer dimensions. But what decides whether an urn goes in, whether it comes out easily, and whether you can see it clearly during a visit is the inner dimension — what is left after the panel thickness is subtracted. Three to five centimetres of difference between these numbers turns one niche into two entirely different products.

For a standard single niche, the common outer dimensions are 400 × 350 × 400 mm, and for high cabinets 400 × 560 × 400 mm. The panel thickness eats into all four sides: the formed vertical panels are 15 mm total each, one on each side; the load-bearing base shelf is a double layer, 30 mm total. So the inner dimension works out to roughly the outer dimension minus 30 mm on each axis, landing at about 370 × 320 × 370 mm. That number is the urn's real house.
I have seen owners bring a 400 × 350 drawing to pair with an urn whose outer diameter is 200 mm, convinced there is plenty of room. In practice, once it is in, less than 85 mm remains on each side. A hand goes in, but it cannot turn. Two people are needed to place or retrieve it; one person simply cannot do it. Whether a niche is usable is obvious on the very first day of interment.
Overall height including the lid, maximum outer diameter including the lid rim, and weight. Three numbers are enough.
A typical single urn is 220–300 mm tall with an outer diameter of 150–200 mm. A double companion urn can reach 350–400 mm. Urns carved from a single block of jade or marble are generally more than twice the weight of ceramic. That weight figure is not for the mover — it is for the base shelf. A double-layer 30 mm shelf handles a conventional ceramic urn without issue, but a 30 kg solid-stone urn placed on the seventh tier will begin to compress and deform from the middle of the top surface first if the load-bearing base is just an ordinary profile. A load-bearing base 120 mm high, 61 mm wide, with 1.5 mm wall thickness and one transverse reinforcing rib in the cavity — when you are specifying for a heavy urn, that set of parameters is not optional. On a niche intended for a heavy urn, the shelf and the base have to be read as one system. Leave out either and you have left in a risk.
A 370 mm clear internal height paired with a 300 mm urn leaves 70 mm. That is comfortable. Build an economy unit at 410 × 320 × 310 and the clear height drops to 280 mm — and that 300 mm urn no longer goes in.
Conversely, plenty of projects compress clear height to 250 mm in order to fit one more tier. A small urn will just barely go in, but during a visit the family has to crouch and tilt their head to look inside. The detail that hurts most in a columbarium is not density. It is being able to see but not see clearly. Those 50 mm buy you the right not to crouch. The dignity of a columbarium design is very often hidden in exactly these few centimetres.

This is the most commonly overlooked point. The door opening of a niche is effectively a second inner dimension. The door frame is 14.7 mm thick, 34 mm wide, 0.7 mm wall thickness, with an integrated hinge channel. Once the door swings open, the clear width you can actually pass through is narrower than the cavity. An urn cannot be pushed in flat; it has to be tilted slightly, so what you really need is the diagonal dimension of the door opening.
So when you inspect a factory, there is only one thing to do: ask them to take a wooden mock-up at the same dimensions as your urn and, in front of you, put it in through the door and take it back out. If they can do it, the inner-dimension design works. If they cannot, that 370 on the drawing is just a number on paper. In this trade, any dimension that has not been physically verified counts as undecided.
A spousal niche is not two single niches side by side. Two 370 mm cavities still have a vertical panel between them, and in use they remain separate. A genuinely usable double niche is a single cavity of 600 mm or more, with only one removable divider in the middle, so the divider can be pulled out when the second interment happens.
The same applies to family niches. Four to six urns arranged on a 600 × 560 × 500 module saves two vertical panels compared with six single cavities, and halves the number of door openings. On a drawing this saves very little money, but in use the difference is large: when the family comes, one door is enough. Once a columbarium reaches family scale, what is being tested is not capacity but single-visit completion. And once the space inside a columbarium has been chopped up, it can never be put back together.
Q: Can the inner dimension be customised to my family's urn?
Yes, but it has to be settled before layout. Niches are arranged in columns, and once a column's inner dimension is set, the whole column follows. Changing it after the frames are installed means rebuilding an entire wall.
Q: The urn is taller — can the shelf be moved up?
On a standard frame the tier heights are modular, and adjusting one level pulls the whole column with it. The right answer is to solve it in the tier configuration: a 3-small/3-large, six-tier frame with a total height of 2,975 mm already reserves the "large" tier for tall urns — provided you thought about where the large urns would go when you laid out the tiers.
Q: Is a bigger inner dimension always better?
No. A larger inner dimension means fewer niches in the same floor area — dozens fewer across a hall, which is a separate line in the total price. Fit for purpose, easy to place and retrieve, and clearly visible: meet those three and you have the right size.
Q: On a tight budget, can we save on the inner dimension first?
Save on the surface finishes, never on the inner dimension. Floor tiles, door panels and light strips in a columbarium can all be replaced in five years. Once the inner dimension is fixed, it cannot be changed for twenty.

The inner dimension of a columbarium niche is a place where centimetres do the talking. Outer dimensions set the price, inner dimensions set the experience, and the door opening decides whether the thing works at all. Measure those three numbers before layout and a niche will never present that particular embarrassment of going in but not coming out, or of being visible but not clear — an embarrassment that, once the frames are up, can only be lived with. The reputation of a columbarium is often damaged in the single moment a family member crouches down.