There is no shortage of advice online about choosing a columbarium niche: check whether the operator is licensed, check whether title is clear, check the operator's philosophy, check the orientation and inauspicious directions. All of it matters. But all of it shares one quality — it lives on paper, and it happens at the moment of signing. The place where a family will actually feel discomfort for twenty years is not in the contract. It is in the thirty seconds after you walk in, pull a door open, and look down.

So when you go to see a columbarium, I suggest bringing three things: a tape measure a phone flashlight, and a bank card. The six tests below can all be measured in ten minutes. What can be measured is a specification. What cannot be measured is only an opinion.
Press the tape measure, or any straight edge, against the underside of the shelf and look for a gap in the middle. On a compliant shelf, sag over one metre should not exceed 1 mm; press down in the middle with the palm of an adult hand and, after releasing, there should be no visible deflection.
A faster method is the bank card: it is 0.76 mm thick. If it slides in, the shelf is already out of flat.
Whether a columbarium shelf sags depends on the carcass. Standard practice for a galvanized steel carcass is 0.5–0.6 mm sheet thickness, a formed vertical panel of 15 mm total thickness, three continuous folds on each side, and a double-layer load-bearing base shelf of 30 mm. Those three folds are not decoration; they are how a thin sheet is given bending resistance. Fold it one time fewer, save a little cost, and by the seventh tier the whole thing starts to settle — and once a niche drops, the door no longer closes properly. The carcass is the only part of this inspection you cannot see, and it is precisely the part you most need to measure.
Stand in front of the door and look at the gap on all four sides. Compliant work has 2–3 mm of gap on all four edges, uniform top to bottom and left to right, with no sense of it widening and narrowing as your finger runs around.
A wide top and a narrow bottom means the niche door frame was set crooked, or the whole column of frames was not levelled. Dead flush on one side and light leaking on the other means the hinge channel position is off. The door frame in a columbarium niche is a profile with an integrated hinge channel (14.7 mm thick, 34 mm wide, 0.7 mm wall). The advantage of an integrated channel is that the holes are formed once at the factory. Where slots have to be cut on site, the cut edge has no anodic protection, and within two or three years white corrosion starts from the cut. The door gap is the most direct report card this process produces, and the first signal of whether a niche will still be usable in twenty years.
The internal clear dimension of a niche must be measured, not read off a drawing. A drawing that says 400 × 350 × 400 outer dimensions implies roughly 370 × 320 × 370 inner — but that is a theoretical value.
Measure at three positions: width and depth at the top, middle and bottom of the cavity. If any of the three differs by more than 2 mm, the shelf is already deflecting under load, or the vertical posts are not plumb. The cavity is the urn's only house. If that number is soft, everything discussed earlier about materials and shaping becomes meaningless. And it is the one parameter in a columbarium that cannot be replaced: door panels can be replaced, lights can be replaced, locks can be replaced, the cavity cannot. Photograph the measurement and file it as a contract annex alongside the as-built drawings.
For this one you need the flashlight. Shine the phone light into the gap between the carcass and the back wall and look at three things: water staining on the carcass back panel, white mould spots, and whether the floor near the wall is dusting or crumbling.
Damp in a columbarium hall does not show on the wall surface. It shows behind. A dry back and a dry floor means moisture control has reached a pass mark. If there is already mould on the back, the damp proofing in this columbarium was surface-only, and what is inside the urns will fail first. The back of a niche is the true water line. Nobody will voluntarily show you this. You have to bend down yourself.

Ask a staff member to demonstrate on the spot: pull a section of light strip out together with its cover, then put it back.
If they can, the top face of the load-bearing base has a concealed light channel (profile 120 mm high, 61 mm wide, 1.5 mm wall, with a channel on the top face). If they cannot, then replacing a single light strip later means dismantling the base and shifting the carcass. Lights in a columbarium are consumables on a five-year cycle. The value of this detail is not today. It is in year five, and in the twenty-year maintenance ledger.
Push the number plate aside and look at the edge of the lock hole. Good work has the hole punched in one operation with a clean edge. Poor work is drilled on site, with burrs left behind — you will know the moment you touch it.
Then check two more things: is the numbering one plate per niche, and can the plate be moved to cover the lock hole; is the lock a uniform brass core, and will a master-key system work. A columbarium is a long-term management operation. Finding a niche quickly and opening locks without confusion depends on these two small components. They occupy a couple of lines on the quotation, but they decide whether this columbarium is "old but orderly" or "old and out of control" ten years from now.
The six items above are measured. Two more are verified: first, the operator's qualifications and facility permits; second, whether you are buying ownership or a right of use, and what happens when the term expires.
Unless these are written into the contract they are worth nothing. A site visit tells you about the niche as a product; a contract tells you about rights. Miss either side and you have not chosen a niche correctly.
Q: What if I don't bring tools?
Use the bank card for the shelf and the phone light for the back panel; the door gap can be judged by eye for consistency. The only item that genuinely needs a tape is the cavity — ask staff to measure it in front of you, and your job is simply to watch whether they measure at the top, middle and bottom. Of these six tests, only that one requires a tool.
Q: Can these details be written into the contract?
Yes, and they should be. Listing sheet thickness, number of folds, profile wall thickness and inner-dimension tolerance as annex specifications is a hundred times more useful than writing "premium materials, quality workmanship".
Q: The niche is already bought. Can anything be fixed?
The inner dimension and the shelf cannot be changed, but the light strip, the door lock and the number plate can all be retrofitted. Of all the hardware in a columbarium, these three are the only parts that can still be upgraded — and the parts that most immediately improve the experience.

Choosing a columbarium niche is, in essence, choosing the condition it will be in twenty years from now. Photographs show you today. A tape measure shows you afterwards. Take those three items on one visit and you will find that the gap between "premium" and "durable" is a few millimetres — and those millimetres happen to be the one thing that cannot be made good after the fact.