Ask a manufacturer "how much can the shelf carry" and most answer "more than enough". That answer carries no information. What you actually need to know: a shelf folded from 1.5 mm steel, spanning 500 mm, has a long-term safe load of 25 to 40 kg, while an urn typically weighs only 3 to 8 kg.

The margin looks generous. But niches never fail because of average weight. They fail because of weight at one point.
Shelf capacity is set by three things: sheet thickness, fold form, and span.
A 1.5 mm cold-rolled steel sheet with a 20 mm return on each side forms a channel section whose bending stiffness is four to five times that of a flat sheet. At a 500 mm span, the long-term no-deflection safe load is 25 to 40 kg. Extend the span to 700 mm and the same sheet carries only 15 to 25 kg.
This is a long-term load, not a "will not collapse" load. Under sustained stress steel slowly deflects — creep. A niche shelf holds its load for decades, so what matters is the load it carries without sagging over thirty years not the load it survives at the moment.
Because the way weight is distributed matters more than the weight itself. A stone urn 200 mm in diameter weighing 8 kg resting on a one-square-metre shelf actually contacts only 0.03 m². That is a concentrated load, and the local stress in the shelf is tens of times what it would be under uniform loading.
Three common mistakes in placing an urn. One: the urn sits against one side, so all the force bears on the folded edge. Two: the urn sits dead centre, which is where deflection is greatest. Three: a thick fabric pad is placed underneath, and once it compresses the urn slowly migrates to the low point.
The correct position is above a stiffening rib, or close to an upright. Niche uprights are typically spaced 900 to 1200 mm apart; placing the urn within 150 mm of an upright minimises the actual stress in the shelf.
The first is fastening. Whether the shelf is fixed to the upright with self-tapping screws or bolts changes capacity by thirty per cent. Self-tapping screws loosen under repeated vibration, and once loose there is only friction.
The second is penetrations. Running strip-light cable or mounting a number-plate bracket means drilling a hole, and each hole severs a load path. Holes in the tension zone — the underside of the shelf — do the most damage.
The third is lateral force. Closing a door, wiping a panel or a family member leaning on it all apply horizontal thrust to the shelf. Shelves that shift sideways in a niche usually do so for this reason, and once shifted, the support at the four corners becomes uneven.

Bring a steel rule and a pencil. Stand the rule vertically at the centre of the shelf and look at the gap between rule and underside; then step three metres back and sight along the row to see whether any cell sits visibly lower.
The second method is pressing: place your palm at the centre, increase force slowly to about 10 kg, release, and listen for a click. A sound means the contact face between shelf and upright is already moving. Niche shelves are a shared structural system along a row; when one sags, its two neighbours follow.
The third method is to look for shims. Paper or timber packers under a shelf mean the installation was not level and settlement will continue.
Moving a niche shelf from 1.2 mm to 1.5 mm adds under one per cent to the material cost of a niche. Moving from 1.5 mm to 2.0 adds about two to three per cent. In other words, load capacity is one of the highest-value upgrades available in a niche.
Conversely some products priced twenty per cent lower save exactly here: 1.0 mm sheet, single-side fold, self-tapping fixings. You cannot see it after installation, but five years later the shelf centre is 3 to 5 mm low, the door gap has widened, and dust gets in.
My advice: write four things into the specification schedule when negotiating — shelf 1.5 mm double-side fold, bolted fixing, span not exceeding 600. Those four are more substantial than finishes or strip lighting, and they cost almost nothing.
Q: A 25 kg shelf with two urns — does that exceed it?
Two urns are at most 16 kg, and with grave goods still under 25 kg. What matters is concentrated load, not total weight.
Q: Can a timber-core shelf be used?
Short term yes, long term no Hall humidity fluctuates widely; timber core absorbs moisture and expands, showing deflection and delamination within two years.
Q: Can a sagging shelf be repaired?
A single shelf can be replaced, provided the module is standard Before buying, ask whether shelves are standard parts and can be replaced individually.

Shelf capacity is not a question of "enough or not" but of "how it is loaded". A 25 to 40 kg safe load against a 3 to 8 kg urn looks ample; but concentrated loading, loosening fixings and drilled penetrations together leave you with half of it. When viewing a niche, press the centre of the shelf — that is worth more than ten assurances.