A row of niches looks like a bank of static cabinets, and in an earthquake it is one of the more dangerous places in the building: tall racks, heavy self-weight, a centre of gravity high up, and irreplaceable contents. Seismic design here is not about keeping the rack upright — it is about keeping the urns in.

Overturning. For a free-standing rack with a height-to-width ratio above three, lateral force tips the whole frame forward. This is the most serious mode; when it happens the entire row is destroyed.
Shelves jumping out. A shelf simply rests on brackets on the uprights with no fixing. Under lateral shaking it slides fore and aft and carries the urn out with it.
Locks springing open. The latch of a cam lock is held by spring pressure; violent shaking can make the door fly open and the urn fall straight out.
Of the three, overturning is a structural problem, while jumping shelves and springing locks are detailing problems. The latter two happen more often and are easier to solve.
A free-standing rack must be connected to the building structure, not rely on its own weight.
The practice: one connection point every 1,200 mm along the back of the rack, using M10 expansion anchors into a concrete wall or structural column with 3 mm angle brackets and an embedment depth of at least 60 mm.
Partition walls — light steel stud, aerated block — cannot be used as the anchor target; you must find a structural column or a ring beam. This is the point most often overlooked in a retrofit of an old building: the wall looks solid but was built later in infill.
Fixing only the base is not enough. Lateral force peaks at the top of the rack, and without restraint there the rack behaves like a standing chopstick — anchoring the foot achieves nothing.
So add a restraint bracket at the top, bearing against the wall or the structure above. Leave a 2 mm gap between bracket and rack: enough for normal movement, not enough for significant displacement.
At the base, in addition to expansion anchors, add anti-slip pads or chemical anchors under the feet. On a tiled floor the anchor must reach the structural slab, not just the levelling screed.
This is the cheapest and most effective measure available.
Back lip. Turn a 15 mm upstand at the rear edge of the shelf so the urn cannot slide backward.
Front lip. A 10–15 mm upstand at the front: normal handling is unaffected, but shaking is contained.
Shelf fixing. Add one self-tapping screw or clip between shelf and bracket to stop fore-and-aft movement. That screw costs under a yuan and prevents most jumping.
Tray restraint. Niches fitted with drawer trays must have a self-locking or damped runner so the tray cannot slide out under shaking.

A cam lock has only 6–8 mm of latch travel and light spring force. Earthquake inertia is easily enough to throw the door clear of the latch.
Three improvements: add a magnetic catch (a magnetic strip in the frame, 2–3 kg of pull); change to a deadbolt-style latch (longer throw, needs alignment hard to spring); add a roller catch (mechanical detent).
Costs run from a few yuan to a few dozen per unit, with a large difference in effect. For seismic upgrading in a columbarium this offers the best value of anything on the list.
Above 2.4 m in height, in addition to wall ties, consider:
- Cross-connections between adjacent racks (angle brackets tying two racks into one body) to raise overall stiffness; - A diagonal brace every 6 m, at 45°–60°; - No heavy objects or stone cladding at the top, to keep the top mass down.
Look at the top. Is there a connector between the top of the rack and the wall? Bottom-only fixing fails.
Push it. Put both hands on the upper part of the rack and feel the movement. If it sways visibly, the ties are inadequate.
Check the shelves. Is there a front lip, and is there a fixing between shelf and bracket?
Check the lock. Close the door and push it lightly; if it moves, the latch is not engaged.
Check the wall. Is the wall the anchors are fixed into a structural wall? Tap it — a hollow sound means partition.
Q: Do low-level niches need seismic measures too?
A: Yes. Low niches still suffer jumping shelves and springing locks; only the overturning risk is smaller. Seismic protection is a whole-system measure, not a high-level-only one.
Q: Can an old columbarium be retrofitted?
A: Yes, with limits Whether wall ties can be added depends on whether the wall is structural; shelf lips can be added later; locks can be changed. Where overturning risk is high, the only option is cross-connection between racks plus bracing.
Q: Do these measures interfere with daily use?
A: No. A 10–15 mm lip does not obstruct handling, and a magnetic catch or roller catch only makes the door close more firmly. Most seismic measures in a niche are of the kind you cannot feel once fitted.

Seismic protection for a niche is not about surviving the big one; it is about not failing in a small one. One self-tapping screw, one 15 mm lip, one magnetic catch — a few dozen yuan, and the three most common failure modes are blocked. Safety in a columbarium never rests on a structural calculation report; it rests on these small things installed inside normally invisible.