The lock on a niche is the one lock in the family's life that gets used a few times in twenty years It does not need to resist picking, but it must meet three conditions: it locks when the door closes, the key never jams, and a spare can still be cut in twenty years. Cam locks and deadbolt latches each have a weakness, and the wrong choice shows up not as theft but as a door that will not open.

Before choosing look at what a niche lock faces:
- Four to twelve operations a year, far below the 3,000 of a domestic door lock; - 55%–85% relative humidity, approaching saturation in the plum-rain season; - Door panel thickness 0.5–1.2 mm, so the lock body has very little depth to work with; - Users mostly middle-aged and elderly with weak grip and poor near vision.
Low frequency, high humidity, shallow mounting, weak operation — those four conditions mean a niche lock should not be specified to a security standard but to a standard of "easy in the hand and it never seizes".
A cam lock (also called a rotating cam lock) has a latch that is a metal plate swinging through 90°; turn the key 90° and it opens. The body is only 15–20 mm deep, which suits the thin door of a niche.
The advantages are speed and tolerance — the key still turns if it is not pushed fully home — plus a simple mechanism, low failure rate and low price.
Three drawbacks:
Short latch. The plate grips the frame by only 5–8 mm, so any panel distortion defeats it.
Spring location. The latch is held in the open or closed position by a spring; once the spring fatigues, the latch drifts and you get "closed but not locked".
Poor pry resistance. A thin plate stops no tool. In a controlled-access columbarium this is not the main issue.
Realistic service life of a cam lock in a niche is five to eight years, failing either as a key that will not turn or a latch that will not return.
A deadbolt latch uses a retractable cylindrical or rectangular bolt entering a hole in the frame, with 10–15 mm of engagement.
The advantages are secure locking, good pry resistance and long life (over ten years). The drawback is that it demands alignment — the lock hole in the panel and in the frame must be on one axis, and a deviation over 2 mm means it will not lock.
The problem is that niche doors are thin and distort easily. After five years, a row will always have a few doors that have sagged slightly, and the deadbolt will not enter.
Deadbolt bodies are also typically 25 mm or more deep, more than the space behind a niche door allows, so a special recessed body is needed at a higher cost.
Standard single niche: cam lock. The door is light the space is shallow, operations are rare — a cam lock is enough. Specify a brass barrel and a stainless latch, never a zinc-alloy latch, which goes brittle in two years.
Family niche, large door: deadbolt latch. The door is heavy and needs to lock solidly, and family niches are usually maintained more attentively, so alignment can be adjusted.
High niches: either, but with a large key bow. Above 1.8 m the keyhole is hard to see, and a bow under 20 mm across is hard to grip.
Not recommended: electronic and keypad locks. Batteries leak in a damp environment within two years, and a niche that cannot be opened because the battery is flat is a serious problem.

When a niche door closes, the latch pulls the panel against the frame, generating a lateral force. That force distorts the panel slightly, and over time the gap becomes wide on one side and narrow on the other.
The fix is a magnetic catch or roller catch on the opposite side of the frame, so the door is located first and locked second. The latch then only locks, it does not locate, and the gap stays stable.
This is uncommon in columbaria but very effective on family niches that are opened often.
Turn it three times. Insert the key and turn it both ways three times. Any binding means the barrel is not machined accurately enough.
Withdraw the key. After locking, feel the resistance as the key comes out. Too loose means a worn barrel; too tight means a poorly toleranced key blank.
Push the door. Once locked, push the panel. More than 2 mm of movement means the latch is not engaging enough.
Check the material. Test the latch with a magnet: if it sticks, it is not stainless. A niche latch must be 304.
Q: What if a key is lost?
A: With a cam lock the barrel can be replaced without changing the whole lock; with a deadbolt latch, usually the whole unit. So when specifying, confirm that the barrel is separately replaceable.
Q: Can one key open a whole row?
A: Yes — that is master-keying. It simplifies management but reduces security. See the next article.
Q: Should the lock be oiled?
A: No. Oil attracts dust and turns to sludge in niche humidity. If it binds, use graphite powder or replace the barrel.

Choosing a niche lock is choosing twenty years without trouble. A cam lock is cheap and easy but works loose; a deadbolt latch locks solidly but must be aligned. Cam locks for standard niches, deadbolts for family niches, 304 stainless latches, separately replaceable barrels — hold those four and no columbarium will ever see the scene of a key that will not turn and a door that has to be taken off its hinges.