A niche is normally an empty cavity with the urn standing on the shelf A tray turns that cavity into a drawer — the urn fixed to the tray, drawn out as a unit. It solves the problem of lifting the urn, and it costs clear height plus a set of runners that will eventually fail.

Niche depth is usually 450 or 550 mm. At 550 mm, a person standing in front can reach about 500 mm, so when the urn sits at the back the fingertips barely hook it.
Inside a niche that becomes trouble in three situations:
- The urn weighs over 10 kg and cannot be held steady one-handed. - The family members are elderly and bending plus reaching is a risk. - The niche is high (above 1.6 m) or low (below 0.4 m).
A tray converts "reach in and lift" into "pull out and lift", changing the action from a bend-and-reach to a standing transfer For elderly visitors that is a substantial difference.
Do this sum before anything else. The tray body (base plus upstand) takes 15–20 mm, the runners or rollers take 5–10 mm, so 20–30 mm in total.
A 450 mm clear niche leaves about 425 mm once a tray is fitted. An urn 400 mm tall on a 30 mm pedestal is already 430 — it will not go in.
So the tray's preconditions are: clear height of at least 480 mm, or an urn no taller than 380 mm. Below that, fitting a tray is boxing yourself in.
Family niches are actually a better fit for trays. With several urns side by side, the tray can be built as one unit and drawn out in a single movement, replacing a series of individual lifts.
The cost of a tray is not in the panel it is in the runners. A three-section ball-bearing slide rated at 15 kg is good for 30,000–50,000 cycles. That sounds like a lot, but the problem in a niche is that it is rarely opened — left idle, the grease dries, the first pull binds; dust settles in the track and the balls seize.
I have seen trays in columbaria that would not move after eight years and the carcass had to be dismantled to get them out.
So specify a demountable construction: the tray lifts off the runners as one piece, and the runners can be replaced on their own. A tray riveted permanently is scrap the day it fails.
One: deepen the shelf front edge. Form a 30 mm downstand at the front of the shelf as a retaining lip, and keep the urn forward so no one has to reach to the back. Zero cost, most practical.
Two: partial extension. The tray covers only the front half with a fixed base and a stop bar behind. A 200 mm pull is enough, the runners are short and the failure rate drops.
Three: a retrieval hook. A 600 mm L-shaped stainless hook to catch the base of the urn and draw it forward. Costs a few dozen yuan and takes no clear height, but it needs technique and is awkward with a heavy urn.
All three are more common in columbaria than a full-extension tray, because none of them sacrifices space.

Fit it: family niches, clear height above 500 mm, urns over 12 kg, mostly elderly visitors, niches at high or low positions.
Do not fit it: standard single niches, clear height under 450 mm light urns, positions between 1.2 and 1.6 m.
Compromise: fit only at high and low positions, leave the middle alone. The comfortable band for a standing person is 1.0–1.6 m, where everything is within reach and a tray earns least.
Pull it three times. Full travel out and back, listening for noise and feeling for end cushioning. A runner without damping hits the stop with a thud, and over time that deforms the limit.
Press it. Draw the tray fully out and load the far end with your palm. More than 10 mm of droop means the runner is undersized.
Rock it. Push sideways; movement should be under 3 mm. More than that means a single-rail construction, which will skew the tray over time.
Check the lock. The tray should have a detent or damper so it does not slide open on contact. Where the niche faces an aisle, this matters particularly.
Q: Will a tray make the urn more likely to fall?
A: No, it is more stable. The urn is fixed to the tray and the tray is captive in the runners, so displacement is less likely than standing loose on a shelf — provided the tray has an upstand or locating recess at least 20 mm high.
Q: Can a tray be added to an existing niche?
A: With difficulty. It means either replacing the shelf, which requires dismantling the carcass, or fitting runners onto the existing shelf, which costs another 10 mm of clear height. This is a design-stage decision.
Q: What material for the tray?
A: Aluminium or stainless, 1.2–1.5 mm. Not blockboard — humidity inside a niche swings, and a timber tray warps and jams the runners within two years.

A niche tray is a choice to trade 25 mm of clear height for not having to bend. It makes sense for elderly visitors and heavy urns; on a standard single niche it is a burden. What actually matters is not whether to fit one, but doing the clear-height sum before you decide — every comfort feature in a columbarium is ultimately deducted from space.