The hinge is the least conspicuous part of a niche and the first to fail. It carries dozens of openings every day and the luck of twenty years without maintenance Of all the hardware in a columbarium it deserves the most careful choice. Between surface-mounted and concealed, the wrong answer is not an aesthetic problem — it is whether the door is still hanging in ten years.

A surface-mounted hinge fixes one leaf to the outside of the frame and one to the back of the panel joined by an exposed pin. Force travels from panel to leaf to pin: a short path through thick components, so a single hinge commonly carries 8–12 kg.
A concealed hinge buries the whole mechanism in a rebate cut into panel and frame, supporting the door through a linkage. The advantage is that no hardware shows once closed — the face is one uninterrupted plane. The drawback is that all the force concentrates at the rebate cut into the panel, and a niche panel is only 0.5–0.8 mm thick.
That is the crucial difference: a surface hinge loads the face of the sheet; a concealed hinge loads a groove in its edge. Rebating a thin panel means removing material from the thinnest part you have.
Run the numbers A 400 × 500 mm panel in 0.8 mm galvanised sheet is 0.2 m²; at a steel density of 7.85 that is about 1.26 kg. Add the viewing glass, number plate and pull, and the whole leaf comes to 1.5–2.5 kg.
Two surface hinges handle that with capacity to spare. So concealed hinges on a niche were never about load — purely about looks. And the price of the look is that the panel must be 1.2 mm or thicker before you dare cut a rebate, or the linkage will wear through the edge of the groove.
Maintenance. Once the linkage loosens, the door first sags, then fails to close properly, then drags. Replacing one hinge means removing the door, removing the lining and re-aligning — three to five times the labour of a surface hinge. This is what operators dread most: in a row of several dozen doors, one failure takes a niche out of service for half a day.
Adjustment range. A surface hinge adjusts by loosening screws and shifting the leaf, 2–3 mm in each direction with almost no tools. A concealed hinge adjusts on an eccentric screw in the linkage, about 1 mm, and only after removing the cover cap.
Cleaning. The concealed hinge rebate is a dust trap; incense ash and dust settle in it and eventually clog the linkage. A surface hinge shows its hardware, but wipes clean in one pass.
Visible hardware. Look along a row and every door carries four metal points, which fragments the visual line. High-end columbaria usually will not accept it, which is why the premium zones of a columbarium mostly stay concealed.
Colour matching. The plating on the hinge rarely matches the door coating exactly, and it dulls over time.
Snagging. A protruding hinge pin can catch a sleeve. Specify a pin with a recessed head and the problem goes away.

Single niches with standard doors: surface-mounted. The door is light it is opened often and repairs need to be quick. When a surface hinge fails, two screws and five minutes.
Family niches, large doors and carcasses built as a single composition: concealed. But only where the panel is at least 1.2 mm and the rebate edge is flanged for reinforcement; otherwise that groove becomes the weak point of the niche. A concealed hinge in a thin panel is a trap you set for yourself.
A mixed arrangement also works: two concealed hinges at the top for appearance, two surface hinges at the bottom for load. On heavy niche doors this is very practical — no hardware visible from the front, and the force lands on thick material.
Count the hinges. Up to 500 mm door height two is enough; over 500, use three; over 700, three minimum. One short and the middle bows.
Look at the pin. A surface hinge pin should be solid stainless, not a plated hollow tube. A magnet tells you: if it sticks, it will rust within two years.
Swing it three times. Listen. Metallic scraping means a dry pin or misalignment; a click means the panel is contacting the frame.
Watch the gap as it opens. Open the door fully and see whether the gap widens noticeably. If it does, the hinge pin is not on the centreline of the panel thickness and over time the panel will distort.
Q: The door is light — is a concealed hinge overkill?
A: It is not overkill, it is risk in the wrong place. Concealing a hinge in a light panel buys appearance and pays for it in durability; the rebate edge is what fails first.
Q: Isn't exposed hardware vulnerable to tampering?
A: A columbarium is a controlled-access space so the risk is low. If you want security, it comes from locks and inspection rounds, not from hiding hinges — which is also why columbaria do not chase concealed hinges.
Q: Should hinges be oiled?
A: A stainless pin can take a little silicone oil. Do not use machine oil — it attracts dust and clogs the pin. Better dry than gummed.

Choosing a niche hinge is a trade between visible appearance and invisible durability. Thin panel, frequent use, fast repair needed: go surface-mounted. Thick panel, composed elevation, uninterrupted face wanted: go concealed, but never on thin sheet. After twenty years in a columbarium, reputation is not decided by how it looked on day one, but by how many doors still open smoothly.