Authenticity Guaranteed

How Wide Should a Double Niche Be?

Category: Technology News Columbarium Date: 2026-10-29 Browse: 13

A double niche looks like "two niches put together", as though you just double the width. It is not. With two urns side by side, you need a gap between them hand clearance on both sides, and a usable door opening. The arithmetic does not give 400 × 2. It starts at 700. A hundred millimetres either way is the difference between "it goes in" and "it comes out".

columbarium design

The width calculation side by side: 520 plus 40 plus 140

Taking the mainstream urn diameter of 260 mm, two urns side by side already need 520 mm. Between them you need a 30 to 40 mm soft divider, or the two urns knock against each other during handling, and a chipped edge on stone is a permanent loss. On each side you need 70 mm of hand clearance so a gloved hand can grip the urn body. 520 + 40 + 140 = exactly 700.

So the minimum internal dimension for a side-by-side double is 700 × 450 × 450. Below that, you can only build a front-to-back or stacked arrangement — which is no longer a side-by-side double.

What actually happens below 700

Doubles with a 600 mm internal width are not uncommon. The method is to place the two urns touching, with no divider. You cannot tell at purchase, but in use three problems appear together.

First, lifting requires both hands hooking at once, with no room to rotate the fingers. Second there is no cushioning between the urns, so the vibration of opening and closing the door transfers straight through. Third, if one urn is larger, the other must lie on its side — and lying on its side is a long-term test of the seal.

In a columbarium these "barely side by side" positions usually cost twenty per cent less than a standard double. They look like a bargain. In fact the trouble has been folded into the price.

Stacked: not saving space, trading one problem for another

When width is insufficient, the conventional solution is stacking. Upper clear height 450, lower clear height 450, with a 30 to 40 mm shelf between, total height reaching 950 to 1000. That needs only 450 mm of width, and it certainly saves floor area.

The cost is in the lower compartment. Its handling height sits 400 to 500 mm off the floor, so you must crouch or bend deeply, and turn your head to avoid the upper door panel. For anyone over sixty this movement is harder than it sounds. There is a reason lower-tier positions are cheap: the discount is paid for in that bending.

Weighing the three arrangements

Side by side at 700 wide: the best sense of ceremony, both urns visible at once, easiest handling. Takes width, so fewer niches per row.

Stacked at 450 wide: saves width, suits narrow column spacing. The lower compartment is laborious to use, and the upper urn's weight bears above the lower, so the shelf must be rated above 40 kg.

Front to back at 550 deep: only 450 mm of width needed, with depth increased beyond 550. The front urn must come out before you can reach the rear one. Suitable for family niches that are rarely opened, not for annual visits that involve handling.

My advice: if you can give 700 mm of width, give it. A double niche is a component decided once and used for decades. Saving one column of positions by choosing stacked means paying that debt at every visit for the rest of your life.

columbarium niche

The two places most often missed when measuring

The first is the door opening. A double's door panel is usually 600 mm or wider, and when opened 90 degrees the panel itself blocks space on one side. What you must measure is the clear distance from the panel edge to the opposite frame when the door is fully open — often 40 to 60 mm narrower than the internal chamber.

The second is the hinge side. If the hinge is on the left, a right-handed person handles it naturally; if the hinge is on the right and you are right-handed, your wrist must fold back. This does not affect dimensions but it affects feel for decades. Open and close the door twice on site and you will know.

Width is not the only difference from two singles

Two single niches are independent: if one fails you repair one, and moving one out does not affect the other. The drawback is two doors, two openings, two numbers and walking back and forth during a visit.

A double solves two people with one door and shortens the route, but structurally it is a long-span cabinet. A shelf spanning 700 mm must be stiffened or it sags in the middle.

So when choosing a double, besides asking about width, ask one more question: "is there a stiffening rib in the middle?" In a long-span cabinet, whether it is there shows in five years.

Frequently Asked Questions

Q: How narrow can a double be?

The functional minimum is 650; the comfortable minimum is 700. Below 650 only small urns fit, and handling requires a tool.

Q: Can two urns of different sizes go side by side?

Yes, but the smaller one needs a levelling block so the urn does not tilt when the door closes. Use EVA or cork, not foam.

Q: Can a double be converted to a single later?

Structurally a divider can be added, but most facilities do not permit it administratively because it involves numbering and ownership. Ask before buying whether it can be divided.

columbarium interior

Conclusion

The width of a double niche is an addition problem: urn diameter times two, plus the soft divider, plus hand clearance on both sides. Niche dimensions are never "close enough" — the 50 mm between 700 and 650 is exactly the distance a hand needs to get in. Bring the urn's measured diameter with you; it is more useful than bringing the budget.

Continue reading articles with the same tags as this one
cache
Processed in 0.005440 Second.