Open a niche door and inside is either bare galvanised sheet or a layer of pale fabric, and the difference in impression is considerable. But lining is not only about looks: it blocks light absorbs impact and prevents scratches, all at once Choose the wrong material and it becomes an odour source inside a sealed box.

Light control. Niches are usually lit by downlight from the lintel, and light striking bare metal bounces a second time, so the inscription on the urn becomes harder to read. A lining turns specular reflection into diffuse reflection and softens the light.
Impact absorption. Doors opening and closing, cleaning knocks, minor tremors — hard contact between urn and metal leaves scratches. A 3–5 mm fabric layer takes that energy.
Concealment. A galvanised interior has folded edges, weld spots and fasteners, and the coating is uneven. Once lined, the cavity is a complete surface.
Conversely, if the interior is powder-coated, the returns are tidy and the lighting is properly designed, lining is a bonus rather than a necessity.
Flock fabric is the mainstream: short pile, 180–250 g/m², with adhesive or a backing board. Good feel, strong light blocking sound absorbent. The drawback is that it traps dust — the pile locks in incense ash, which cannot be shaken out, only vacuumed.
Non-woven is cheap, blocks light moderately, and its advantage is that it does not shed and can be wiped. Suits a budget carcass; a grade below flock in appearance.
Foil-faced foam goes where moisture control matters: the foil blocks vapour, the foam absorbs impact. But foil reflects under the light and reads as a bright patch from the front, which is the worst appearance of the three It is normally confined to side walls and ceiling, never the back panel.
Choosing between them is essentially picking two of three: appearance, cleanability, moisture resistance.
This is the most overlooked point. Once the door closes, a niche is a nearly sealed volume, and whatever the adhesive gives off cannot escape — it stays inside and deposits on the urn and the walls.
Three families of lining adhesive are common:
- Solvent-based neoprene: strongest bond, strongest smell, VOC release lasting more than six months. Not recommended inside a niche. - Water-based: low odour, weak initial grab, needs 24 hours under clamping. The compromise option. - Hot-melt or self-adhesive hook-and-loop: solvent-free, purely mechanical fixing. Cleanest, but poor heat resistance — it can let go in a hot warehouse in summer.
The most stable method I have seen in a columbarium is clips plus hook-and-loop: the lining is made as a removable fabric box, its edges tucked into the profile groove, the corners located with hook-and-loop, and no adhesive at all. Two years later, changing the lining means sliding it out.
Fully glued and sealed down. The tighter it is stuck, the less replaceable it is. A lining has a service life: after five years the pile is full of dust and the colour has gone dull, and if it cannot be changed it stays ugly.
Dark colours. Deep red and deep brown read heavy under niche lighting, and any damp leaves tide marks that stand out against a pale urn. Columbarium linings are mostly beige, light grey and oatmeal, which reflect more and make the urn look brighter.
No access points. A lining applied over the whole surface hides stiffeners fasteners and lighting cable. Any future service means tearing it off.

A lining costs clear height. Five millimetres at the top, five at the bottom three on the back panel: a 450 mm clear niche becomes about 437 mm usable.
That sounds small, but an urn 400 mm tall on a 30 mm base is already 430, leaving 7 mm. So fix the urn first, then the lining thickness — never the other way round Family niches, holding several urns, usually line only the side walls and back, leaving ceiling and floor bare, precisely to save those two centimetres.
Smell. Open the door: is there a sharp adhesive odour? If so, the adhesive has not cured or a solvent type was used.
Feel. Press the lining; it should give 2–3 mm and should not feel rigid. Rigid means the backing or the adhesive layer is too thick.
Pull. Grip the edge and pull gently: it should move slightly without coming away. Falling off means the adhesive has failed; immovable means it is glued down for good.
Look at the edges. The lining should be tucked into a groove or covered by a trim strip. Exposed raw edges lift within six months.
Q: Is lining mandatory?
A: No. A columbarium with well-finished powder coating and considered lighting looks fine unlined. But most mid- and low-priced niches have weld marks and colour variation inside, where lining is the best value step available.
Q: How often does a lining need replacing?
A: Flock 3–5 years, non-woven 2–3. The criterion is not time but whether the pile has matted and the colour greyed. A removable system takes two hours to change; a glued one takes a full day.
Q: Does lining affect ventilation in the niche?
A: Yes. Fabric itself breathes, but a lining covering the entire back panel without openings will block the breathing holes in the carcass. Cut openings at those positions, or build the lining as panels that leave the holes clear.

Lining is the last step that turns an industrial box into a place where something can be kept. Its value is not in how expensive the material is, but in whether the adhesive is the right type, whether it can be removed and replaced, and whether the colour is chosen to last. The niches in a columbarium that make people linger are usually not the flashy ones — just clean, even and odourless.